Handover in LimeSDR
hello is it possible if i have 2 eNB using LimeSDR connected to the same EPC(SRSran for example) to do a handover from 1 eNB to a other and if yes is there any extra equipment needed on a other hand...
View ArticleLimeSDR mini v2.2 problems, completely lost!
Hi all, Just new to this world and already regretting my choices in life! I have a LimeSDR mini v2.2 I have been to the MyriadRF pages for support and found a lot on LimeSDR or firmware for LimeSDR...
View ArticleLimeSDR XTRX phase noise
Has the TX and RX phase noise of the LimeSDR XTRX been specified or better still, measured? I have located the data sheet for the on board Rakon E8582LF TXCO. Rick 2 posts - 2 participants Read full...
View ArticleLime Mini 2 - Botched FPGA upload
Salutations and greetings from Sunny Bangkok, This is my first posting. I need help as I think I have caused the FPGA to be erased somehow. I received my brand new Lime SDR Mini2 today from Crowd...
View ArticleLimeSDR Mini 2.0 for AM 1570 kHz DRM digital radio modulator
Hi We are considering in buying a LimeSDR Mini 2.0, but noticed the frequency range is: 10 MHz - 3.5 GHz We are looking at using it as a DRM digital radio modulator for a radio station that broadcasts...
View ArticleLimeSDR Mini V2.0 - max data bitrate "dualRXTX" mode
Hello, I plan to buy LimeSDR Mini V2.0, please clarify this point: what is the maximum data bitrate possible via the USB interface in the “dualRXTX” mode? 5 posts - 2 participants Read full topic
View ArticleNew LimeSDR Mini V2 Stopped
Hello I just removed my LimeSDR Mini V2 from my PortDown Box which had been working very well, as I was going to mount into a metal case, until this is had been working extremely well since I received...
View ArticleARM SBC can't see Mini 2
I just got an Orange Pi 5 and I was trying to see if I could make my code run on it. I’m having a problem that the USB host can’t see the Mini, even though it must be alive because I get the heartbeat...
View ArticleLimeSDR Mini 2.0 RX only works after changing bandwidth
Hello, SDR noob here. When trying to use my LimeSDR mini 2.0 in SDR++ or URH on Linux, when I initially start the stream I don’t get any data. However, if I then change the bandwidth to some different...
View ArticleLimeSDR Mini v1.1 vs. v1.2 (and later)
Greetings, Upon looking at the schematics for the LimeSDR Mini v1.1 vs. v1.2, I noticed that v1.2 switched from using the internal LDO’s to supplying the 1.2V and 1.4V externally. What was the...
View ArticleLimeSDR USB return TransferPacket: Read failed (ret=0)
Hello all, The LimeSDR USB is showing TransfertPacket errors during LimeQuickTest. I using ubuntu 18.04, 20.04 and windows 10 operating system. I update the LimeSDB USB board with latest firmawre with...
View ArticleLimeSDR USB as a RFID reader 13.56MHz iso14443
Hello, I puchase an antenna for 13.56Mhz frequency, I would like to know if it is possible to read/write RFID card. As you know RFID card are powered by the field. So is the LimeSDR is able to provide...
View ArticleLimeSDR Mini 2.0 passes FTDI configuration but fails LimeQuickTest
LimeSDR newcomer here. I have a LimeSDR Mini 2.0 purchased from Crowdsupply. I am attempting to verify functionality of the device using LimeQuickTest. The following steps on Windows 10 have been...
View ArticleTransmitted signal at 100MHz visible at 5700MHz
Hi all, I plugged the TX of a Lime to the RX of a Blade, transmitted a 2MHz wide noise around 100MHz, and I could see it while receiving at 5700MHz. I put a band pass filter that greatly filters...
View ArticleLimeSDR-Mini v2.4 - external clock
I have version v2.4 but on the page is only version v2.2 https://limesdr-mini.myriadrf.org/ I want to use an external clock with LimeSDR Mini On the website it is written “(remove R63 and solder...
View ArticleDismal performance in HF
I finally got my lime to transmit with SDR angel. However the signal power drops off like a rock and is unusable under 25Mhz. Am i doing something wrong? 1 post - 1 participant Read full topic
View ArticlePower save mode
Hi Currently i am setting sampleRate to 1e6, oversample to 2 (in order to get lock) and: EnableChannel(true, 0, false); EnableChannel(true, 1, false); EnableChannel(false, 0, false);...
View ArticleClik here to view.
Getting up and running with LimeSDR XTRX
Hi. I just received LimeSDR XTRX. But I can’t find a suitable driver and software for Windows. I confirmed that the device was correctly recognized as a Xilinx’s device (10EE) by Device Manager, but...
View ArticleLimeSDR mini on Ubuntu
Hello! We are trying to run tests with a LimeSDR mini v1.3 on Ubuntu 20.04. We have installed everything, including the LimeSuite version and other related components, but when running LimeQuickTest...
View ArticleRegarding low LimeRFE RF Output Power
Currently I already received a new LimeRFE after waiting almost 1 year. I hook up my new LimeSDR mini with LimeRFE and I run my python program with GNU Radio components at 144MHz, sadly I only got...
View Article