Lime Mini V2 - Low Frequency Works
Hi, I am new to the Lime Mini V2. Is it possible to listen to 2M AM radio and transmit (TX) on a 500 kHz frequency? Also, is there a consultant available for hire or support for custom applications?...
View ArticleClik here to view.
LimeSDR USB Receiver issues
Greetings All, It seems that my LimeSDR USB is failing some of the LimeQuickTest: … [ TESTING STARTED ] ->Start time: Wed Oct 30 08:21:56 2024 ->LimeSuite version: 22.09.1-ge83c13b9 ->Device:...
View ArticleQuestion regarding how 2 SDRs running simultaneously are timed
I have 2 LimeSDR Minis (v 2.4) that are connected to the same clock. I am running them simultaneously and am not surprised that their output is not synchronized in time. What does puzzle me is the...
View ArticleLimeSDR Mini-v2 FPGA Test Benches & FIFODC
Hello, I’ve been looking through the LimeSDR-Mini-v2_GW gateware repo in attempts to make some modifications to the rxtx data flows, and I ran into issues while trying to make use of the included test...
View ArticleClik here to view.
Why is Onetone pulsing?
I used to be able to play the Onetone frequency and I would see a pure sine wave on my reciever, after a program crash my Onetone (and any other waveform) seem to pulse instead of transmitting a...
View ArticleLimeSDR Mini V2.0
Hi, I am new to the SDR & RF world, so apologies if question’s too broad. I am trying to get DVBS/S2 RF output from TS stream for testing purposes. I understand this is possible with LimeSDR Mini...
View ArticleClik here to view.
High phase noise on Lime xtrx
I have an lime xtrx v1.2 board. If apply a sine wave to the input, the timing diagram shows high phase noise. I think this is due to the instability of lo. Please tell me how to fix this. The...
View ArticleLime XTRX external clock
How сonfigure Lime XRTX to use an external clock signal? Is it possible to use internal gps receiver for more clock stability? 1 post - 1 participant Read full topic
View ArticleLimesdr mini 2.0 and trunk-recorder
Anyone have any luck getting lime sdr mini 2.0 working with trunk-recorder. I can get it to see the sdr. But my gains aren’t working correctly. Not sure how to define them. Hopeing to take a peek at...
View ArticleIQ data capturing
Hi, I am new to limesdr. My task is to read IQ data using limesdr. While exploring I found that file sink is used to capture the IQ data. So I used File sink block in my flowgraph. After running the...
View ArticleStarting with LimeSDR Mini v2.4 on Linux
Hello, I just received my new LimeSDR Mini v2.4 board and I wanted to start with. On Windows I was able to run SDR Console to receive and transmit, but now I want to use it on my linux machine -...
View ArticleMissing R114 on XTRX recommendation
I’m one of the unfortunate ones that received an XTRX with the missing R114 resistor. I am apprehensive about altering the board by bridging the pad because I suspect that any warranty or adjustment...
View ArticleUsing the LimeSDR Mini 2.0 for through-wall gesture detection
I used the LimeSDR mini 2.0 as a radar device for detecting hand points and gestures through occlusions! I made a video about it that I thought the community here might find interesting. LoRF-Ha: AI...
View ArticleRF loopback test fails with "TuneVCO(CGEN) - failed to lock (cmphl!=3)"
Hi friends! I recently purchased a LimeSDR mini. LimeQuickTest is failing with: TuneVCO(CGEN) - failed to lock (cmphl!=3) SetFrequencyCGEN(61.44 MHz) failed Does anyone have any suggestions for how to...
View ArticleClik here to view.
XTRX max limelight frequency
What is the max limelight interface frequency? I see there was some fine tuning of the Xilinx FPGA drive parameters to increase limelight interface max speed, what is the speed that was acheived?...
View ArticleLimeSDR-Mini 2.0 - LimeQuickTest FAILED!
Hello everyone, I have the LimeSDR-Mini 2.0 (v2.2) and when I do the LimeQuickTest I have a failure. I am using the Master repository. This is what I get : Card15Nodd:~$ LimeQuickTest [ TESTING...
View ArticleXTRX enumeration issue
Greetings! I’m having an issue with a physical xtrx 1.2 device. I’m wondering if this could be either the device doesn’t have any configuration on it, or perhaps EEPROM / Flash corruption? The PCIe...
View ArticleSynchronize two/three/four LimeSDR-XTRX
I need to start several LimeSDR-XTRX devices to receive or transmit synchronously. Unfortunately, I haven’t found a clear instruction on how to do it. I am writing my code in C++ on Linux. I need...
View ArticleLimeSDR-XTRX StatusCallbackFunc is not called
There is the “StreamConfig” structure that helps to config settings for a stream in StreamConfig.h file. In “StreamConfig” structure we can find the definition of the function that gets called...
View ArticleLimeSDR-XTRX how to use GPS chip on board
There is a global positioning system chip on LimeSDR-XTRX board. Unfortunately, I did not find any suitable functions in the API to work with this chip. Please tell me how to work with this chip from...
View Article